Comments to this Manuals Your Name. Connect the equipment onto an outlet on a circuit different from that to. Install the edge connector of the add-on card into the expansion slot. The language bar will then appear as fol- lows. These manyal are well amnual and will only fit in one orientation. Manuap to the following: Click to open the language control panel.
Click to enter the normal OS you have installed such as Mnual. The CPU may experience overheating so it will shutdown to protect itself. The max point reward for answering a question is Refer to the table below for information: Login to post Please use English characters only.
Jumpers with more than one pin are numbered. When installing a CPU heatsink and cooling fan make sure that you DO NOT scratch the motherboard or any of the surface- mount resistors with the clip of the cooling fan. Below you can find a brief description of each software program, and the location for your motherboard version. Chapter 6 Trouble Shooting Start up problems during assembly After assembling the PC for the first time you may experience some start up problems.
Not finding what you are looking for? Please visit our website for updated manual. In the default, S3, the suspend mode is a suspend to RAM, i. Click Next run the Installation Wizard. Load Default Settings Load Default Settings This option opens a dialog box g41 lets you install stability-oriented defaults for all appropriate items in the Setup Utility.
Version 2. Page 4 Integrated Peripherals Page 10 Memo Introducing the Motherboard Page Checking Jumper Settings Do not over-tighten the screws as this can stress the motherboard.
Checking Jumper Settings This section explains how to set jumpers for correct configuration of the motherboard. Setting Jumpers Use the motherboard jumpers to set system configuration options. Jumpers with more than one pin are numbered. Pin 1 is labeled.
If the clip of the cooling fan scrapes across the motherboard, you may cause serious damage to the motherboard or its components. Read and follow the instructions shown on the sticker on the CPU cap.
The total memory capacity is 16 GB. Page Expansion Slots Expansion Slots Installing Add-on Cards The slots on this motherboard are designed to hold expansion cards and connect them to the system bus. Page 20 Follow these instructions to install an add-on card: Remove a blanking plate from the system case corresponding to the slot you are going to use.
Install the edge connector of the add-on card into the expansion slot. Ensure that the edge connector is correctly seated in the slot. Secure the metal bracket of the card to the system case with a screw. Additionally, some computer cases have USB ports at the front of the case. If you have this kind of case, use auxiliary USB connector to connect the front-mounted ports to the motherboard. Page 23 COM1: Onboard serial port header Connect a serial port extension bracket to this header to add a second serial port to your system.
These connectors are well designed and will only fit in one orientation. Page Installing A Floppy Diskette Drive Installing a Floppy Diskette Drive FDD1: Floppy Disk Connector Connect the single end of the floppy connector to the onboard floppy connector firstly, and then connect the remaining plugs on the other end to the floppy drive correspondingly.
Page Connecting Case Components Connecting Case Components After you have installed the motherboard into a case, you can begin connecting the motherboard components. The main menu of the Setup Utility displays a list of the options that are available. A highlight indicates which option is currently selected. Use the cursor arrow keys to move the highlight to other options. Page Standard Cmos Setup For the purpose of better product maintenance, the manufacture reserves the right to change the BIOS items presented in this manual.
If the feature is enabled, it will enhance hard disk performance by reading or writing more data during each transfer. Page Advanced Setup Advanced Setup This page sets up more advanced information about your system.
Handle this page with caution. Page 17 Due to chipset limitation, please follow closely the table below when installing memory for dual channel or single channel mode operation.
Memory Installation Combination For dual channel configuration, you must always install identical the same board, speed, size and chip-type DDR2 DIMM pair in the slots of the same color.
Page Expansion Slots Expansion Slots Installing Add-on Cards The slots on this motherboard are designed to hold expansion cards and connect them to the system bus.
Page 20 Follow these instructions to install an add-on card: Remove a blanking plate from the system case corresponding to the slot you are going to use. Install the edge connector of the add-on card into the expansion slot. Ensure that the edge connector is correctly seated in the slot. Secure the metal bracket of the card to the system case with a screw.
It elimi- nates limitations of the current Parallel ATA interface. But maintains register com- patibility and software compatibility with Parallel ATA. Page 23 COM: Onboard Serial Port header Connect a serial port extension bracket to this header to add a second serial port to your system. Page 25 Refer to the illustration below for proper installation: Attach either cable end to the connector on the motherboard.
Attach the other cable end to the SATA hard drive. Page Connecting Case Components Connecting Case Components After you have installed the motherboard into a case, you can begin connecting the motherboard components. Page Standard Cmos Setup For the purpose of better product maintenance, the manufacture reserves the right to change the BIOS items presented in this manual.
If the feature is enabled, it will enhance hard disk performance by reading or writing more data during each transfer. Handle this page with caution. Any changes can affect the operation of your computer. Page Integrated Peripherals Integrated Peripherals This page sets up some parameters for peripheral devices connected to the system.
Page Pc Health Status PC Health Status On motherboards support hardware monitoring, this item lets you monitor the parameters for critical voltages, temperatures and fan speeds. The max data from PECI is zero. If the over-clocking fails, please turn offthe system power. New BIOS provides support for new peripherals, improve- ments in performance, or fixes for known bugs.
Below you can find a brief description of each software program, and the location for your motherboard version. Select from the menu which software you want to install. Page 49 Click Next. The following screen appears: Check the box next to the items you want to install. The default options are recom- mended. Click Next run the Installation Wizard. An item installation screen appears: Follow the instructions on the screen to install the items.
Drivers and software are automatically installed in sequence. Continue this process to complete the drivers installation.
DOC file in the root directory. User Playback Audio speaker function working b. Page 53 3.
0コメント